Watch batteries WIP: Difference between revisions
No edit summary |
|||
| Line 57: | Line 57: | ||
| style=width:200px; text-align:left;" |[[File:Watch back showing notch for winder and O ring.jpg|thumb|165x165px|left|Watch back showing O ring and also the notch for winder.]] | | style=width:200px; text-align:left;" |[[File:Watch back showing notch for winder and O ring.jpg|thumb|165x165px|left|Watch back showing O ring and also the notch for winder.]] | ||
|Examine the back. Look at the O ring and check it is undamaged. Identify the notch on the back for the winder. You will need to orientate the back so that the notch is over the winder when you re-assemble the watch. | |Examine the back. Look at the O ring and check it is undamaged. Identify the notch on the back for the winder. You will need to orientate the back so that the notch is over the winder when you re-assemble the watch. | ||
|} | |} | ||
| Line 89: | Line 77: | ||
=== Screw-on watch backs=== | === Screw-on watch backs=== | ||
====Tools==== | |||
[[File:3-point case opener.jpg|left|thumb|200px|A 3-point watch back remover]] | |||
A 3-point watch back remover is essential. Watch repair kits often come with a 2-point tool. You can use this, but you will find the 3-point version more stable and easier to use, and well worth the modest extra cost. | |||
====Removing the back==== | |||
[[File:Screw-on_watch_back.jpg|right|thumb|200px|A screw-on watch back.]] | |||
This type of watch back typically has 6 indentations around its circumference. This is easily removed with a 3-point watch back removal tool. It may come with several sets of points which can be adjusted to precisely fit the indentations in the watch back. Gently but firmly twist the back anticlockwise in order to remove it. | This type of watch back typically has 6 indentations around its circumference. This is easily removed with a 3-point watch back removal tool. It may come with several sets of points which can be adjusted to precisely fit the indentations in the watch back. Gently but firmly twist the back anticlockwise in order to remove it. | ||
[[File:3-point watch back remover in use.jpg|right|200px|thumb|A 3-point watch back remover in use.]] | |||
To replace the back, make sure it's correctly placed. If you twist it anticlockwise with your fingers you should feel a slight click as the thread engages. Now turn it clockwise, first with your fingers and then with the tool. | To replace the back, make sure it's correctly placed. If you twist it anticlockwise with your fingers you should feel a slight click as the thread engages. Now turn it clockwise, first with your fingers and then with the tool. | ||
=== Screwed-on watch backs === | === Screwed-on watch backs === | ||
| Line 101: | Line 93: | ||
== Replacing the battery == | == Replacing the battery == | ||
{| | |||
| style=width:200px; text-align:left;" |[[File:Inside to show battery.jpg|left|thumb|165x165px|left|You can see the battery and the spindle for the winder.]] | |||
|You should now see the inside of your watch. If you do not know what battery is needed, you can see the number on the old battery. In the photograph the battery number is 364. Renata is the make, but there are many other makes of battery. | |||
Sometimes you might find the battery is held in place by a metal finger secured by a tiny screw. Loosen the screw only enough to move the finger away from the battery. Replacing the screw if it comes out is tricky, but easier with a magnetised screwdriver. | |||
|- | |||
| style=width:200px; text-align:left;" |[[File:Removing the battery.jpg|thumb|165x165px|left|Removing the battery. Needle is for illustration only]] | |||
|If you have the replacement battery, you can remove the old battery. The battery is held by retaining clips on edge of the battery. Sometimes it helps to use a sewing needle to push the battery out, starting from the outer edge. | |||
|- | |||
| style=width:200px; text-align:left;" |[[File:Watch with battery removed.jpg|left|thumb|165x165px|left|Watch with battery removed]] | |||
|Here you can see the watch after the battery has been removed. | |||
You can now insert the new battery with the writing on the top as it was with the old battery. It should not require force to get the battery back in position. | |||
|} | |||
== Replacing watch straps == | == Replacing watch straps == | ||
Revision as of 13:08, 19 November 2022
This page describes how you can change watch batteries yourself.
Summary
Most watch batteries are easy to replace. This guide is for watches with a snap fit back and not a screw-on back. (That will be added later. A snap fit back is the commonest type.
Safety
- To do this task you need a watch press otherwise you will either be unable to replace the back, or you might break the glass
- Do dispose of the old battery properly. Keep batteries out of the way of children as they can be fatal if swallowed.
Tools
You can get a tool kit quite cheaply from eBay and other sites containing most of the basic tools you'll need, and you can supplement this as required. They will pay for themselves with the savings from changing just a few watch batteries
Here are some general tools you may find useful. (More specialised tools are listed in the relevant sections below.)
- Error creating thumbnail: File missing
A dust puffer - may be useful for expelling dust if it gets into a watch.
- Error creating thumbnail: File missing
A set of precision screwdrivers or a selection of flat and cross-head jeweller's screwdrivers is likely to be needed.
- Error creating thumbnail: File missing
A magnetiser (or any neodynium magnet you might happen to have) for magnetising screws, making them much easier to manipulate.
- Error creating thumbnail: File missing
Straight and angled tweezers may be useful. (If used for watch batteries, always hold them across a diameter, not across the flats.)
- Error creating thumbnail: File missing
You may find a jeweller's eye loupe helpful.
- Error creating thumbnail: File missing
You will need a good light or a head torch.
Consumables: IPA, tissues, spare batts
Removing and replacing watch backs
Snap-on watch backs
Tools and consumables
The following inexpensive special tools will be needed:
- Error creating thumbnail: File missing
A case-opening knife or a flat screwdriver with a thin blade is required to remove the back.
- Error creating thumbnail: File missing
A watch press (shown here with a watch in place) with a relection of dies is essential for replacing the back.
In addition, the following general tools:
- A bright light or a head torch.
- If you use reading glasses, you will need to use them. A magnifying glass or jeweller's eye loupe is helpful.
Consumables:
- A replacement battery. Ideally you should use the internet to find out the battery that fits your watch. There are many different types of watch battery and they can be bought at a good hardware store, or Amazon or eBay. Of course if you cannot find out which battery is required, you can open the watch and see the battery that is in place.
- Isopropyl alcohol and tissues.
Removing the back
Clean the back of the watch with isopropyl alcohol giving particular attention to the join between the back and the body of the watch.
| Examine the edge of the back piece to find the small raised area where you will insert your screwdriver.Make a note or take a photograph of the back. Note the position of the winder when the writing is the right way up. | |
| Carefully insert the screwdriver into the gap in the lift off area. Twist and the back should pop off. | |
| Examine the back. Look at the O ring and check it is undamaged. Identify the notch on the back for the winder. You will need to orientate the back so that the notch is over the winder when you re-assemble the watch. |
Replacing the back
Your watch press should come with a selection of dies that screw into place. You need to select the underside die that supports/contacts the metal case only. Too small means that the edge of the die is pressing on the glass. Too big means that the main part of the die is in contact with the glass and the outer ring is not on the metal case. The choice is crucial to avoiding damage to the glass.
- Error creating thumbnail: File missing
Ideal placement with die in contact with watch case only.
- Error creating thumbnail: File missing
Die is too small and only in contact with the watch face.
- Error creating thumbnail: File missing
Die is too big and pressing on the watch face.
The upper die will press on the watch back to snap into place. The die has to be at least as wide as the watch back, but the choice is less critical.
One the dies have been screwed onto the pegs of the watch press, carefully place the watch onto the lower die. The put the back onto the watch making sure that the cut-out for the winder shaft is over the shaft. Make sure the back is aligned evenly and is not tilted.
| Gently squeeze the handles together so that the upper die contacts the back and check that it is even. Then increase the force of your squeeze and you should hear/feel a snap as the back goes into place. |
Screw-on watch backs
Tools
A 3-point watch back remover is essential. Watch repair kits often come with a 2-point tool. You can use this, but you will find the 3-point version more stable and easier to use, and well worth the modest extra cost.
Removing the back
This type of watch back typically has 6 indentations around its circumference. This is easily removed with a 3-point watch back removal tool. It may come with several sets of points which can be adjusted to precisely fit the indentations in the watch back. Gently but firmly twist the back anticlockwise in order to remove it.
To replace the back, make sure it's correctly placed. If you twist it anticlockwise with your fingers you should feel a slight click as the thread engages. Now turn it clockwise, first with your fingers and then with the tool.
Screwed-on watch backs
Some more words and pics
Replacing the battery
| You should now see the inside of your watch. If you do not know what battery is needed, you can see the number on the old battery. In the photograph the battery number is 364. Renata is the make, but there are many other makes of battery.
Sometimes you might find the battery is held in place by a metal finger secured by a tiny screw. Loosen the screw only enough to move the finger away from the battery. Replacing the screw if it comes out is tricky, but easier with a magnetised screwdriver. | |
| If you have the replacement battery, you can remove the old battery. The battery is held by retaining clips on edge of the battery. Sometimes it helps to use a sewing needle to push the battery out, starting from the outer edge. | |
| Here you can see the watch after the battery has been removed.
You can now insert the new battery with the writing on the top as it was with the old battery. It should not require force to get the battery back in position. |
Replacing watch straps
Some more of my words and pics
Replacing watch glasses
A watch with a broken, cracked or scratched glass can be repaired. At a jeweller's this might be quite expensive and you may find that you can do it yourself for less, including the cost of a spcial tool and a set of replacement watch glasses. Pics of glass grabber and set of watch glasses
Additional pics:
- Error creating thumbnail: File missing
A watch strap holder.
- Error creating thumbnail: File missing
A spring bar remover.
- Error creating thumbnail: File missing
A link remover.
- Error creating thumbnail: File missing
A 3 point case opener.
- Error creating thumbnail: File missing
A nylon mallet.